This post is the twelfth in a set for the 12 calendar months that began with March. Graphs are sixteen-year logs of the monthly mean anomaly values of nine climate variables for Manilla, NSW, with fitted trend lines. I have explained the method in notes at the foot of the page.

Raw anomaly values for February

Extreme values of February anomalies were as follows:

Daily Maximum Temperature Anomalies (3) -4.2 deg: February 2008; -3.3 deg: February 2012; -3.3 deg: February 2013;
Daily Mean Temperature Anomalies (1) -3.3 deg: February 2008;
Rainfall Anomalies (1) +120 mm: February 2012;
Dew Point Anomalies (2) -4.6 deg: February 2014; -4.6 deg: February 2015.

Trend lines for February

Heat Indicators

All heat indicator quartic trends began slightly low and ended slightly low. They had a low peak about 2004, and a trough later. The trough was deepest and earliest for daily maximum temperature (2011), followed by daily mean temperature in 2012, daily minimum temperature in 2014, and subsoil temperature in 2015 or later.

Moisture indicators

Quartic trend lines for moisture indicators began steady near or slightly below zero. They rose to peak values, then fell.

Dew Point Anomaly reached a low peak in 2007, and ended very low.
Minus (Temperature Range Anomaly) peaked in 2007, and ended neutral.
Moisture Index peaked in 2009, and ended low.
Rainfall Anomaly reached a high peak in 2010, and ended low.
Cloudiness Anomaly peaked in 2012, and ended high.

---

Notes.

Anomaly values

Each data point is an anomaly value that is the difference between  the mean value for a month and the normal value for that calendar month. Normals are based on the decade beginning March 1999, except that rainfall normals are based on 125 years from 1883.
Raw anomaly values vary a lot from month to month, and different variables often do not move in the same sense.
(Raw values for variables in a given month are in a report for that month. Look for the report for a given month in the “Archive” for the month following it.)

Heat Indicators

Four of the anomalies of variables are grouped as indicators of the anomaly of sensible heat at the site: daily maximum air temperature, daily minimum air temperature, daily mean air temperature (mean of maximum and minimum) and subsoil temperature (at 750 mm).

Moisture Indicators

The anomalies of five more variables are grouped as moisture indicators relating to latent heat rather than sensible heat. They are: rainfall total (mm), percent cloudy mornings (>4 octas), early morning dew point,  daily temperature range (minus), and a composite measure called “Moisture Index”. For plotting, the observed anomaly values of percent cloudy mornings have been divided by ten and the observed anomalies of monthly total rainfall in millimetres have been divided by twenty. In the same way, the moisture index is calculated as:

MI = ((Rf anom/20)+(%Cloudy anom/10)+(DP anom)+(-(TempRange anom)))/4

Dew point values are problematic. Early values were estimated from remote readings, some of which seem too high; recent values use an instrument capable of reading very low humidity values, some of which are surely too low.

Trend lines

Changes in raw anomaly values are very large from year to year and show no clear pattern. To reveal a pattern calls for trend lines to be fitted.
When I fit linear trend lines, they have almost no meaning. They have R-squared values around 0.01! That is, linear trend lines “explain” hardly any of the variation. When I fit trend lines that are parabolic, cubic, or quartic the R-squared value goes up, until it is around 0.3 for quartic trends. (Quartic trends “explain” about 30% of the variation.) Beyond quartic functions, there are not enough data points to justify fitting the trend line.
Quartic trend lines can identify up to three local extreme points, whether maxima or minima, if they exist in the data.